激情加勒比东京热国产_久久久久毛片精品_欧洲免费毛片在线_欧美黑人两根一起进3p_美国男女日b视频播放_欧洲一级片网址无码性生活_中文无码乱伦av_91精品毛片在线_日本成人久久大黄_中文字幕25天天夜夜

彩盒爆邊的原因人盡皆知，無非是水份含量與紙張耐折度太低，天氣干燥等原因所致，下面介紹幾個實用解決辦法

1、在上光時保持適度干燥，一般采用大口徑抽風道并在烘道上安裝水冷卻裝置，這樣可避免彩紙在干燥固化時過于干燥及紙張發脆現象。

2、通常情況下，裱彩紙后紙板的水份含量可達10％以上。但天氣高溫干燥而待裱紙板的水份含量非常低的情況下，膠水的水份很快蒸發，裱出的紙板水份仍然很低。此時不妨使用自裱機的濕水輥，在紙板背面濕水，同時選用固含量低的膠水并加大上膠量，這樣便可以迅速提高裱出紙板的水份含量。

3、對于裱好的彩紙、如果水份含量太低，可用一臺單色膠印機或柔印機在紙板的背面印一遍水，印水后用保鮮膜將紙板包裹嚴實，等到第二天紙板水分平衡后再進行模切。注意，模切后立即進行粘盒，若需放置一段時間再粘盒也需用;拉伸膜;包裹，以免水分過早散失。

對于多數單坑紙板彩盒，由于搖蓋在折疊時抗張強度不高，爆線問題較少。但是對于高強瓦紙且是雙瓦楞的紙板，單憑增加水份也不容易解決。

白咭涂層耐折性測試方法：

 用裁紙刀裁切尺寸為250＊50mm的試樣五條（注意確保紙的直紋方向與長邊垂直），在溫濕度為23±1℃，52±2％的環境下存放4小時。

b)將試樣向內彎折使兩條短邊重疊，注意保持試樣中間部位呈圓弧狀。

c)將彎折后試樣置于一10KG重的壓輥下，按住重疊的一端，推動壓輥向試樣中間圓弧部位碾過，使碾過后的試樣呈對折狀。

d) 往復碾壓五次后打開試樣，觀察碾出的壓折紙表面涂層是否有爆裂現象。如無任何爆裂，則表明該白咭涂層耐折良好；如有輕微爆裂，則白咭涂層耐折一般；如果出現明顯爆裂，則表明該白咭涂層耐折較差。

（1）合理設計模切版

優質的壓痕鋼線應硬度適中，穩定性強，刀頭圓滑，圓弧中軸對稱，高度、厚度偏差小，規格齊全。其選用原則是：壓痕鋼線的厚度不小于紙厚，高度等于模切刀片高度減去模切材料厚度，再減去修正值0.05～0.10mm。壓痕線的選用原則是：壓痕線的厚度也不小于紙厚，寬度等于紙厚的1.5倍加上壓痕鋼線的厚度。

開連點本質上是在模切刀刃口部位開出一定寬度的小口，使模切后的紙盒和廢邊不散開，便于排廢。連點通常開在產品成型后不易看到的隱蔽處，并且要避開膠線位置。如果不得已連點在成型后能夠看見，則連點應越小越好，否則排廢時連點處不易分離，導致紙張撕爛及附近墨層爆線。連點寬度=紙厚+0.20mm。

（2）當壓痕鋼線之間的距離過小時，需粘貼海綿膠條以起到反拉力的作用，把紙張壓緊，減輕壓力。另外，校板時可在壓線位開出凹槽形狀，使彩盒折疊成型時有一個較大的弧度，從而起到減輕爆線的作用。

（3） 如果客戶沒有特別要求，又沒有耐折性更好的白卡紙，建議彩紙改用覆膜工藝，可一勞永逸

Color box burst edge is well-known, but the water content and paper folding is too low, dry weather and other reasons, here are a few practical solutions 1, in glazing to maintain a moderate dry, general use of large-diameter air duct and drying channel installed on the water cooling device, so as to avoid the paper in the drying and curing too dry paper brittle phenomenon. 2. Usually, the moisture content of paper board can reach more than 10% . But when the temperature is high and dry and the moisture content of the board is very low, the moisture of the glue evaporates quickly, and the moisture of the board is still very low. At this point may wish to use the self-laminating machine of the wet water roll, in the back of the paper board wet water, at the same time choose a low solid content of glue and increase the amount of glue, so as to quickly increase the moisture content of the paper board. 3. For the color paper, if the moisture content is too low, you can use a single color offset printing machine or flexo printing machine on the back of the paper, printed water, with plastic film will be wrapped tightly, wait until the next day after the paperboard moisture balance for die-cutting. Note that the best immediately after die-cutting sticky box, if you need to place a period of time and then sticky box also need; stretch film; wrapping, so as not to lose moisture too early. For most single pit cardboard color box, due to the swing cover in the folding tensile strength is not high, burst line problems are less. But for high-strength corrugated paper and is double corrugated cardboard, simply increase the moisture is not easy to solve. Test Method for folding resistance of White Card coating: Five samples of 250 * 50 mm cut with a paper cutter (make sure that the straight line direction of the paper is perpendicular to the long side) are stored for 4 hours at 23 & AMP; Plusmn; 1 °C, 52 & amp; plusmn; 2% . B Bend the sample inward so that the two short edges overlap, keeping the middle part of the sample in an arc shape. C place the bent specimen under a 10KG weight press roller, press and hold the overlapping end, push the press roller to roll over the middle arc of the specimen, so that the rolled specimen is folded in half. D Rolling five times and then open the sample to observe whether the surface coating of the rolled Origami paper has burst. If there is no burst, the white card coating has good folding resistance; if there is a slight burst, the white card coating has good folding resistance; if there is a significant burst, the white card coating has poor folding resistance. (1) reasonable design of die-cutting high-quality indentation steel wire hardness moderate, strong stability, round head, arc axis symmetry, height, thickness deviation small, complete specifications. The selection principle is: the thickness of indentation steel wire is not less than paper thickness, height is equal to die-cutting blade height minus die-cutting material thickness, and then minus the correction value of 0.05 ~ 0.10 mm. Indentation Line selection principle is: indentation line thickness is not less than the paper thickness, width equal to 1.5 times the thickness of the indentation steel line thickness. In essence, the point is in the die-cutting edge of a certain width of the small mouth, so that the die-cutting box and waste edge does not spread, easy to discharge waste. Connecting points are usually opened in the product after the molding is not easy to see the hidden place, and to avoid the location of the glue line. If you have to connect the point after the formation can see, the smaller the connection point should be as good as possible, or waste removal when the connection point is not easy to separate, resulting in paper tearing and near the ink layer burst line. Connecting point width paper thickness + 0.20 mm. (2) when the distance between the indentation steel wire is too small, need to paste sponge tape to play the role of anti-tension, the paper pressure, reduce the pressure. In addition, when the school board can be in the pressure line to open a groove shape, so that the color box folding molding has a larger arc, thus play a role in reducing the explosion line. (3) if the customer has no special requirements, and do not have a better folding resistance of white cardboard, the proposal to use color paper laminating process, can once and for all